SPRINT3X

zzoota’s most discrete device.

 

The Legalities

Copyright

All Rights Reserved.

This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission.

Disclaimer

The information in this document is subject to change without prior notice in order to improve the reliability, design and function. It does not represent a commitment on the part of the manufacturer. Under no circumstances will the manufacturer be liable for any direct, indirect, special, incidental, or consequential damages arising from the use or inability to use the product or documentation, even if advised of the possibility of such damages.

User Manual Contents

Congratulations on the purchase of your new zzoota Sprint3X!
This User Manual is your guide for getting started with the key functions of your Sprint3X.

For installation and technical details, please follow our Installation Guide.

 

  1. Safety Instructions

  2. Warranty Information

  3. Sprint3X Introduction

    3.1. Spint3X Overview
    3.2. Specifications

  4. Getting Started

    4.1. Charging the Sprint3X
    4.2. Powering On and Off
    4.3. SIM Card

  1. Safety Instructions

  • Read all cautions and warnings on the equipment.

  • Place this equipment on a reliable surface when installing.

  • Dropping it or letting it fall may cause damage.

  • Make sure the correct voltage is connected to the equipment.

  • Keep this equipment away from humidity.

  • Disconnect this equipment from the A/C outlet before cleaning it.

  • Do not use liquid or sprayed detergent for cleaning.

  • Do not scratch or rub the screen with a hard object.

  • Never use any of the solvents, such as thinners, wax, benzene, abrasive cleaners, acid or alkaline solvents on the display. Harsh chemicals may cause damage.

  • Remove dirt with a lightly moistened cloth and a mild solvent detergent. Then wipe the enclosure with a soft dry cloth.

  • If the device will not be used for an extended period, disconnect it from the power source to avoid damage by transient over-voltage.

  • Never pour any liquid into openings. This may cause fire or electrical shock.

 

Do not use the device if:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user’s manual.
e. The equipment has been dropped or damaged.
f. The equipment has obvious signs of breakage.

 

2. Warranty

Click here for zzoota’s warranty policy, or to make a claim.

 

3. Sprint3X Introduction

3.1 Sprint3X Overview

 

3.2 Specifications

Physical Characteristics

Dimensions
84 x 42 x 14mm

Weight
50g

Dust and Water Resistance Rating

Communication

Communication System
Cat M1

Antenna
Multi-band
Internal

GPS

Chipset
U-blox 7

Accuracy
<10m

Interface

I/O Type
SOS/MIC/Tele-Cutoff (petrol/electricity)/ACC

Tamper Alert
Light sensor

Power

Battery
270mAh/3.7V industrial grade Lithium Polymer

Working Voltage
9 -90V

Working Current
<30mA 12V

Sleep Current
<3mA 12V

Environmental Requirements

Operating Temperature
-20ºC to 70ºC

Storage Temperature
-40ºC to 85ºC

Humidity
-

 

4. Getting started

4.1 Powering On and Off

The Sprint3X arrives switched on – and once receives power, it will turn on quickly. See the LED Status section of this manual to diagnose your Sprint3X. When unpowered, the device will stay on for a short time, then go to sleep.

4.2 SIM Card

When you receive your device, it will come with a SIM card preinstalled for your convenience, unless otherwise discussed with zzoota.

If you need to change the SIM card for any reason, follow the below steps:

  1. Remove the back of the device. Due to the waterproofing, the back of the device snaps into place and can be hard to remove – be careful not break the teeth holding it in place, or to pull on the external wires.

  2. Turn the device off

  3. Unlock the metal plate holding the SIM in place by sliding it in the indicated direction and lift it up. Do not attempt to lift the metal plate when it is in the locked position.

  4. Remove current SIM card – note the orientation of the card

  5. Insert new SIM card, using the same orientation as the previous card

  6. Lower the metal plate, and slide into the locked position.

  7. Turn the on

  8. Put the back of the device into place. Ensure it is completely flush with the front of the device.

Note: If the supplied SIM card is removed and inserted into another device, it will deactivate. Reactivating the SIM card will require the completion of a Support Ticket, and may incur a fee.

4.3 LED Status

Blue Light:

Slow Blinking - The device is finding a GPS position. Keep the device powered until it finds a GPS position.

Continuous - The device has found a GPS position

Red Light:

Slow Blinking - The device is searching for a network

Fast Blinking - The device has found a network

Continuous - The device is connected to a network

LED Off - If this occurs after the device has been on for 5 minutes, the device has gone into power save mode.

FAQ

  • Find our installation guide here.

    • Check to see if the device has been added to your account. You can do this by reading the IMEI (Serial Number) on the back if your device, and checking it against the object window in Link. If it does not appear, the Manager of your account can add it to the platform following this guide .

    • If the device appears in the object window of Link., make sure it is ticked.

    • Ensure “objects” are toggled ON in the map view options on the right side of the screen.

    • The Sprint3X must be receiving power to ping – make sure it has been properly installed following our guide.

    • If the SIM card has been removed and placed into another device, it will deactivate as a security feature. Record the number on the SIM card, and submit a Support Ticket to reactivate. Costs may apply.